Kreg Jig Material Support Stop Manuel d'utilisateur télécharger pdf

Pivot Pin

Nylon Bolt

Knurled

Nylon Lock

Nut

Arm

Base

Hex Nut

*Mini Trak T-Nut

*Mini Trak Bolt

Kreg Jig

®

Support Stop

Assembly and Instructions

R

Version 2005701

NK7520

Assemble the Kreg Jig

®

Support/Stop

1. Slide the center tongue of the Support/Stop Arm between the outside extensions of the

Support/Stop Base and align the pivot hole through all three surfaces.

2. Insert the Pivot Pin through one outside surface of the Support/Stop Base and either tap into

place with a mallet or a hammer and a block of wood to prevent marring the end of the Pivot Pin.

Continue to advance the Pivot Pin until it is fully seated in the Support/Stop Base and Support/

Stop Arm. Push the 1/4”-20 Hex Nut into the side of the Support/Stop Arm hex recess.

3. Thread the Nylon Stop Bolt from either side through the Support/Stop Arm into the Hex Nut.

Which side will depend on which side of the Kreg Jig

®

that the Support/Stop will be used.

4. Thread the Knurled Nylon Lock Nut onto the Nylon Stop Bolt on the side of the Support/Stop

Arm opposite the Hex Nut. It may be necessary to thread the Knurled Nylon Lock Nut onto the

Nylon Stop Bolt prior to threading the Nylon Stop Bolt into the Hex Nut in some applications.

*Note: Mini Trak Bolt & T-Nut provided for use with Kreg Mini Trak, (KMS7506) sold separately.

Pivot Pin

Nylon Bolt

Knurled

Nylon Lock

Nut

Arm

Base

Hex Nut

*Mini Trak T-Nut

*Mini Trak Bolt

Kreg Jig

®

Support Stop

Assembly and Instructions

R

Version 2005701

NK7520

Assemble the Kreg Jig

®

Support/Stop

1. Slide the center tongue of the Support/Stop Arm between the outside extensions of the

Support/Stop Base and align the pivot hole through all three surfaces.

2. Insert the Pivot Pin through one outside surface of the Support/Stop Base and either tap into

place with a mallet or a hammer and a block of wood to prevent marring the end of the Pivot Pin.

Continue to advance the Pivot Pin until it is fully seated in the Support/Stop Base and Support/

Stop Arm. Push the 1/4”-20 Hex Nut into the side of the Support/Stop Arm hex recess.

3. Thread the Nylon Stop Bolt from either side through the Support/Stop Arm into the Hex Nut.

Which side will depend on which side of the Kreg Jig

®

that the Support/Stop will be used.

4. Thread the Knurled Nylon Lock Nut onto the Nylon Stop Bolt on the side of the Support/Stop

Arm opposite the Hex Nut. It may be necessary to thread the Knurled Nylon Lock Nut onto the

Nylon Stop Bolt prior to threading the Nylon Stop Bolt into the Hex Nut in some applications.

*Note: Mini Trak Bolt & T-Nut provided for use with Kreg Mini Trak, (KMS7506) sold separately.

1 2

Kreg Jig 1
Support Stop 1

Résumé du contenu

Page 1 - Support Stop

Pivot PinNylon BoltKnurledNylon Lock NutArmBaseHex Nut*Mini Trak T-Nut*Mini Trak BoltKreg Jig®Support StopAssembly and InstructionsRVersion 2005701NK7

Page 2

Material Support/Stop (Fig. 2A-D)The Material Support/Stop is a dual function feature that both “Supports” large panels to keep them perpendicular to

Commentaires sur ces manuels

Pas de commentaire